x

Suggestion/Complaint


Machine Tools Accessory

Machine Tools Accessory

View as
per page
Picture of Live Centre for Lathe Machine-Taper No. 5........

Live Centre for Lathe Machine-Taper No. 5........

Live or revolving center A live center or revolving center is constructed so that the 60° center runs in its own bearings and is used at the non-driven or tail stock end of a machine. It allows higher turning speeds without the need for separate lubrication, and also greater clamping pressures.......
Call for pricing
Picture of Filter Cartridge for Transformer Oil Centrifuging Machine-Hole Size (50 Micron).............

Filter Cartridge for Transformer Oil Centrifuging Machine-Hole Size (50 Micron).............

A filter intended to remove impurities from transformer oil or hydraulic oil is called an oil filter cartridge. Many different kinds of transformer oil filteration plants, hydraulic equipment, etc. use oil filter cartridges................
Call for pricing
Picture of Chuck-4 Jaw (Dia 400 MM).........

Chuck-4 Jaw (Dia 400 MM).........

Chuck-4 A jaw is a holding mechanism used in lathes and drills that centralises the work piece or tool by allowing multiple adjustable jaws to move in tandem..........
Call for pricing
Picture of Vice Bench-8" (Inch).........

Vice Bench-8" (Inch).........

A mechanical tool called a bench vise is used to hold an object while it is being worked on. Its design incorporates two parallel jaws..........
Call for pricing
Picture of Air Filter Regulator-12KG/CM2.........

Air Filter Regulator-12KG/CM2.........

Air Filter Regulator is a unit that regulates air filters (FR Unit) In compressed air systems. .........
Call for pricing
Picture of Air Filter Regulator-7KG/CM2.......

Air Filter Regulator-7KG/CM2.......

Liquid water and particle matter are eliminated from compressed air sources using air filter regulators. These are "mechanical filters" and do not get rid of chemical or oil vapour pollutants. .........
Call for pricing
Picture of Vice Bench-4 (Inch).......

Vice Bench-4 (Inch).......

A mechanical tool called a vice bench vise is used to hold down an object while it is being worked on. The gadget is widely utilised in a variety of industries, including the mechanical and woodworking ones........
Call for pricing
Picture of V-Pulley Belt Section-335MM, Groove 10

V-Pulley Belt Section-335MM, Groove 10

V-belt pulleys, also known as vee belt sheaves, are mechanisms that transfer power between axles using a mechanical coupling with a trapezoidal cross section called a v-belt. Together, these components provide a slip- and misalignment-resistant high-speed power transmission solution.
₹ 23,909.00 ₹ 26,299.90
Picture of Impact Wrench-3/4 Inch Square Drive, Maximum Torque 1800NM, 40V

Impact Wrench-3/4 Inch Square Drive, Maximum Torque 1800NM, 40V

An impact wrench is a socket wrench power tool designed to produce high torque output with low user effort by storing energy in a rotating mass and then delivering it abruptly to the output shaft.
₹ 28,463.00 ₹ 31,309.30
Picture of Hydraulic Thruster Brake (36Kg) for 200 MM Brake Drum

Hydraulic Thruster Brake (36Kg) for 200 MM Brake Drum

Hydraulic Thruster Brake is a tool used to keep stationary moving machinery at a slower speed. By using a lever/rod system, the spring applies the braking force to the shoes.
₹ 11,196.00 ₹ 12,315.60
Picture of Hydraulic Coupler (Gun End)-1/8 BSP, 3 JAW

Hydraulic Coupler (Gun End)-1/8 BSP, 3 JAW

Hydraulic Coupler use used to connect and disconnect fluid lines quickly and easily. They give customers the opportunity to quickly attach and detach hydraulic lines from tools or add-ons.
₹ 854.00 ₹ 939.40
Picture of Insert for Face Milling Cutter-Dia 125MM with Lead Angle 45 Deg.

Insert for Face Milling Cutter-Dia 125MM with Lead Angle 45 Deg.

Cutting tools in milling machines include holders and milling inserts. To cut metals, etc., by rotating, cutting tooth (inserts or heads) are attached to a main unit (holder), which is then attached to a machine tool, such as a machining centre with a tool holder.
₹ 6,313.00 ₹ 6,944.30
Picture of Insert for Face Milling Cutter-Dia 80MM with Lead Angle 59 Deg.

Insert for Face Milling Cutter-Dia 80MM with Lead Angle 59 Deg.

Cutting tools in milling machines include holders and milling inserts. To cut metals, etc., by rotating, cutting tooth (inserts or heads) are attached to a main unit (holder), which is then attached to a machine tool, such as a machining centre with a tool holder.
₹ 6,300.00 ₹ 6,930.00
Picture of Insert for Extended Flute Milling Cutter-Dia 63MM, No. of Insert:20

Insert for Extended Flute Milling Cutter-Dia 63MM, No. of Insert:20

When removing a thick layer of material, extended-flute cutters are put under a great amount of strain, and their operation under such demanding cutting conditions is characterised by high cutting forces, significant power consumption, and significant heat generation.
₹ 6,186.00 ₹ 6,804.60
Picture of Insert for Shell Milling Cutter-Dia 80MM with Lead Angle True 90 Deg.

Insert for Shell Milling Cutter-Dia 80MM with Lead Angle True 90 Deg.

Cutting tools in milling machines include holders and milling inserts. To cut metals, etc., by rotating, cutting tooth (inserts or heads) are attached to a main unit (holder), which is then attached to a machine tool, such as a machining centre with a tool holder.
₹ 3,656.00 ₹ 4,021.60
Picture of Revolving Center (High Speed, Extended Point)-MT4

Revolving Center (High Speed, Extended Point)-MT4

Revolving centres, often referred to as rotating centres or running centres, are utilised at the non-driven or tail stock end of a machine so that the 60° centre runs in its own bearings. Greater clamping pressures and faster turning speeds are both made possible without the need for additional lubrication.
Call for pricing
Picture of Revolving Center (High Speed, Stub Point)-MT4

Revolving Center (High Speed, Stub Point)-MT4

Revolving centres, often referred to as rotating centres or running centres, are utilised at the non-driven or tail stock end of a machine so that the 60° centre runs in its own bearings. Greater clamping pressures and faster turning speeds are both made possible without the need for additional lubrication.
Call for pricing
Picture of Keyless Drill Chuck-1-13MM with MT-2

Keyless Drill Chuck-1-13MM with MT-2

A Keyless Drill Chuck allows you to replace the drill bits without having to use any special keys. The main advantage of this type of chuck is that it makes the process of replacing bits much faster. You can place the bit inside the chuck and then tighten the chuck around it by twisting.
Call for pricing
Picture of Revolving Center (Slow Speed Application)-MT4, 3 Bearing Design

Revolving Center (Slow Speed Application)-MT4, 3 Bearing Design

Revolving centres, often referred to as rotating centres or running centres, are utilised at the non-driven or tail stock end of a machine so that the 60° centre runs in its own bearings. Greater clamping pressures and faster turning speeds are both made possible without the need for additional lubrication.
Call for pricing
Picture of Revolving Center (Slow Speed Application)-MT4, 4 Bearing Design

Revolving Center (Slow Speed Application)-MT4, 4 Bearing Design

Revolving centres, often referred to as rotating centres or running centres, are utilised at the non-driven or tail stock end of a machine so that the 60° centre runs in its own bearings. Greater clamping pressures and faster turning speeds are both made possible without the need for additional lubrication.
Call for pricing